| Commit message (Collapse) | Author | Files | Lines |
|---|
|
From the Spec "4.3.5 Erase":
The host should adhere to the following command
sequence: ERASE_WR_BLK_START, ERASE_WR_BLK_END and
ERASE (CMD38).
If an erase (CMD38) or address setting (CMD32, 33)
command is received out of sequence, the card shall
set the ERASE_SEQ_ERROR bit in the status register
and reset the whole sequence.
Reset both addresses if the ERASE command occured
out of sequence (one of the start/end address is
not set).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-5-f4bug@amsat.org>
|
|
As it is legal to WRITE/ERASE the address/block 0,
change the value of this definition to an illegal
address: UINT32_MAX.
Unfortunately this break the migration stream, so
bump the VMState version number. This affects some
ARM boards and the SDHCI_PCI device (which is only
used for testing).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-4-f4bug@amsat.org>
|
|
'0' is used as a value to indicate an invalid (or unset)
address. Use a definition instead of a magic value.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-3-f4bug@amsat.org>
|
|
Trace addresses provided to the ERASE command.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201015063824.212980-2-f4bug@amsat.org>
|
|
The Descriptor Table has a bit to allow the DMA to generates
Interrupt when the operation of the descriptor line is completed
(see "1.13.4. Descriptor Table" of 'SD Host Controller Simplified
Specification Version 2.00').
If we have pending interrupt and the descriptor requires it
to be generated as soon as it is completed, reschedule pending
transfers and yield to the CPU.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-5-f4bug@amsat.org>
|
|
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-4-f4bug@amsat.org>
|
|
If we have pending DMA requests scheduled, process them first.
So far we don't need to implement a bottom half to process them.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-3-f4bug@amsat.org>
|
|
Clearing BlockCount stops multiple transfers.
See "SD Host Controller Simplified Specification Version 2.00":
- 2.2.3. Block Count Register (Offset 006h)
- Table 2-8 : Determination of Transfer Type
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200903172806.489710-2-f4bug@amsat.org>
|
|
The 'Transfer Block Size' field is 12-bit wide.
See section '2.2.2. Block Size Register (Offset 004h)' in datasheet.
Two different bug reproducer available:
- https://bugs.launchpad.net/qemu/+bug/1892960
- https://ruhr-uni-bochum.sciebo.de/s/NNWP2GfwzYKeKwE?path=%2Fsdhci_oob_write1
Cc: qemu-stable@nongnu.org
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Fixes: d7dfca0807a ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Prasad J Pandit <pjp@fedoraproject.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-3-f4bug@amsat.org>
|
|
Add datasheet name in the file header.
We can not add the direct download link since there is a disclaimers
to agree first on the SD Association website (www.sdcard.org).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-3-f4bug@amsat.org>
|
|
Add missing newline character in qemu_log_mask() format.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200901140411.112150-2-f4bug@amsat.org>
|
|
If the M-profile low-overhead-branch extension is implemented, FPSCR
bits [18:16] are a new field LTPSIZE. If MVE is not implemented
(currently always true for us) then this field always reads as 4 and
ignores writes.
These bits used to be the vector-length field for the old
short-vector extension, so we need to take care that they are not
misinterpreted as setting vec_len. We do this with a rearrangement
of the vfp_set_fpscr() code that deals with vec_len, vec_stride
and also the QC bit; this obviates the need for the M-profile
only masking step that we used to have at the start of the function.
We provide a new field in CPUState for LTPSIZE, even though this
will always be 4, in preparation for MVE, so we don't have to
come back later and split it out of the vfp.xregs[FPSCR] value.
(This state struct field will be saved and restored as part of
the FPSCR value via the vmstate_fpscr in machine.c.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-11-peter.maydell@linaro.org
|
|
M-profile CPUs with half-precision floating point support should
be able to write to FPSCR.FZ16, but an M-profile specific masking
of the value at the top of vfp_set_fpscr() currently prevents that.
This is not yet an active bug because we have no M-profile
FP16 CPUs, but needs to be fixed before we can add any.
The bits that the masking is effectively preventing from being
set are the A-profile only short-vector Len and Stride fields,
plus the Neon QC bit. Rearrange the order of the function so
that those fields are handled earlier and only under a suitable
guard; this allows us to drop the M-profile specific masking,
making FZ16 writeable.
This change also makes the QC bit correctly RAZ/WI for older
no-Neon A-profile cores.
This refactoring also paves the way for the low-overhead-branch
LTPSIZE field, which uses some of the bits that are used for
A-profile Stride and Len.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-10-peter.maydell@linaro.org
|
|
In arm_cpu_realizefn(), if the CPU has VFP or Neon disabled then we
squash the ID register fields so that we don't advertise it to the
guest. This code was written for A-profile and needs some tweaks to
work correctly on M-profile:
* A-profile only fields should not be zeroed on M-profile:
- MVFR0.FPSHVEC,FPTRAP
- MVFR1.SIMDLS,SIMDINT,SIMDSP,SIMDHP
- MVFR2.SIMDMISC
* M-profile only fields should be zeroed on M-profile:
- MVFR1.FP16
In particular, because MVFR1.SIMDHP on A-profile is the same field as
MVFR1.FP16 on M-profile this code was incorrectly disabling FP16
support on an M-profile CPU (where has_neon is always false). This
isn't a visible bug yet because we don't have any M-profile CPUs with
FP16 support, but the change is necessary before we introduce any.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-9-peter.maydell@linaro.org
|
|
v8.1M's "low-overhead-loop" extension has three instructions
for looping:
* DLS (start of a do-loop)
* WLS (start of a while-loop)
* LE (end of a loop)
The loop-start instructions are both simple operations to start a
loop whose iteration count (if any) is in LR. The loop-end
instruction handles "decrement iteration count and jump back to loop
start"; it also caches the information about the branch back to the
start of the loop to improve performance of the branch on subsequent
iterations.
As with the branch-future instructions, the architecture permits an
implementation to discard the LO_BRANCH_INFO cache at any time, and
QEMU takes the IMPDEF option to never set it in the first place
(equivalent to discarding it immediately), because for us a "real"
implementation would be unnecessary complexity.
(This implementation only provides the simple looping constructs; the
vector extension MVE (Helium) adds some extra variants to handle
looping across vectors. We'll add those later when we implement
MVE.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-8-peter.maydell@linaro.org
|
|
v8.1M implements a new 'branch future' feature, which is a
set of instructions that request the CPU to perform a branch
"in the future", when it reaches a particular execution address.
In hardware, the expected implementation is that the information
about the branch location and destination is cached and then
acted upon when execution reaches the specified address.
However the architecture permits an implementation to discard
this cached information at any point, and so guest code must
always include a normal branch insn at the branch point as
a fallback. In particular, an implementation is specifically
permitted to treat all BF insns as NOPs (which is equivalent
to discarding the cached information immediately).
For QEMU, implementing this caching of branch information
would be complicated and would not improve the speed of
execution at all, so we make the IMPDEF choice to implement
all BF insns as NOPs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-7-peter.maydell@linaro.org
|
|
The BLX immediate insn in the Thumb encoding always performs
a switch from Thumb to Arm state. This would be totally useless
in M-profile which has no Arm decoder, and so the instruction
does not exist at all there. Make the encoding UNDEF for M-profile.
(This part of the encoding space is used for the branch-future
and low-overhead-loop insns in v8.1M.)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-6-peter.maydell@linaro.org
|
|
The t32 decode has a group which represents a set of insns
which overlap with B_cond_thumb because they have [25:23]=111
(which is an invalid condition code field for the branch insn).
This group is currently defined using the {} overlap-OK syntax,
but it is almost entirely non-overlapping patterns. Switch
it over to use a non-overlapping group.
For this to be valid syntactically, CPS must move into the same
overlapping-group as the hint insns (CPS vs hints was the
only actual use of the overlap facility for the group).
The non-overlapping subgroup for CLREX/DSB/DMB/ISB/SB is no longer
necessary and so we can remove it (promoting those insns to
be members of the parent group).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-5-peter.maydell@linaro.org
|
|
v8.1M brings four new insns to M-profile:
* CSEL : Rd = cond ? Rn : Rm
* CSINC : Rd = cond ? Rn : Rm+1
* CSINV : Rd = cond ? Rn : ~Rm
* CSNEG : Rd = cond ? Rn : -Rm
Implement these.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-4-peter.maydell@linaro.org
|
|
From v8.1M, disabled-coprocessor handling changes slightly:
* coprocessors 8, 9, 14 and 15 are also governed by the
cp10 enable bit, like cp11
* an extra range of instruction patterns is considered
to be inside the coprocessor space
We previously marked these up with TODO comments; implement the
correct behaviour.
Unfortunately there is no ID register field which indicates this
behaviour. We could in theory test an unrelated ID register which
indicates guaranteed-to-be-in-v8.1M behaviour like ID_ISAR0.CmpBranch
>= 3 (low-overhead-loops), but it seems better to simply define a new
ARM_FEATURE_V8_1M feature flag and use it for this and other
new-in-v8.1M behaviour that isn't identifiable from the ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-3-peter.maydell@linaro.org
|
|
For nested groups like:
{
[
pattern 1
pattern 2
]
pattern 3
}
the intended behaviour is that patterns 1 and 2 must not
overlap with each other; if the insn matches neither then
we fall through to pattern 3 as the next thing in the
outer overlapping group.
Currently we generate incorrect code for this situation,
because in the code path for a failed match inside the
inner non-overlapping group we generate a "return" statement,
which causes decode to stop entirely rather than continuing
to the next thing in the outer group.
Generate a "break" instead, so that decode flow behaves
as required for this nested group case.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-2-peter.maydell@linaro.org
|
|
Commit 7998beb9c2e removed the ram_size initialization in the
arm_boot_info structure, however it is used by arm_load_kernel().
Initialize the field to fix:
$ qemu-system-arm -M n800 -append 'console=ttyS1' \
-kernel meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0
qemu-system-arm: kernel 'meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0' is too large to fit in RAM (kernel size 1964608, RAM size 0)
Noticed while running the test introduced in commit 050a82f0c5b
("tests/acceptance: Add a test for the N800 and N810 arm machines").
Fixes: 7998beb9c2e ("arm/nseries: use memdev for RAM")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201019095148.1602119-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
VMStateDescription.fields should be end with VMSTATE_END_OF_LIST().
However, microbit_i2c_vmstate doesn't follow it. Let's change it.
Fixes: 9d68bf564e ("arm: Stub out NRF51 TWI magnetometer/accelerometer detection")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201019093401.2993833-1-liangpeng10@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Unlike many other bits in HCR_EL2, the description for this
bit does not contain the phrase "if ... this field behaves
as 0 for all purposes other than", so do not squash the bit
in arm_hcr_el2_eff.
Instead, replicate the E2H+TGE test in the two places that
require it.
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The reporting in AArch64.TagCheckFail only depends on PSTATE.EL,
and not the AccType of the operation. There are two guest
visible problems that affect LDTR and STTR because of this:
(1) Selecting TCF0 vs TCF1 to decide on reporting,
(2) Report "data abort same el" not "data abort lower el".
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We already have the full ARMMMUIdx as computed from the
function parameter.
For the purpose of regime_has_2_ranges, we can ignore any
difference between AccType_Normal and AccType_Unpriv, which
would be the only difference between the passed mmu_idx
and arm_mmu_idx_el.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The IRQ values are defined few lines earlier, use them instead of
the magic numbers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add trace events for GPU and CPU IRQs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Current documentation is not too clear on the GETPC usage.
In particular, when used outside the top level helper function
it causes unexpected behavior.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Message-id: 20201015095147.1691-1-e.emanuelegiuseppe@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This test exercises the various modes of the npcm7xx timer. In
particular, it triggers the bug found by the fuzzer, as reported here:
https://lists.gnu.org/archive/html/qemu-devel/2020-09/msg02992.html
It also found several other bugs, especially related to interrupt
handling.
The test exercises all the timers in all the timer modules, which
expands to 180 test cases in total.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20201008232154.94221-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
When TBI is enabled in a given regime, 56 bits of the address
are significant and we need to clear out any other matching
virtual addresses with differing tags.
The other uses of tlb_flush_page (without mmuidx) in this file
are only used by aarch32 mode.
Fixes: 38d931687fa1
Reported-by: Jordan Frank <jordanfrank@fb.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201016210754.818257-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
On ARM, the Top Byte Ignore feature means that only 56 bits of
the address are significant in the virtual address. We are
required to give the entire 64-bit address to FAR_ELx on fault,
which means that we do not "clean" the top byte early in TCG.
This new interface allows us to flush all 256 possible aliases
for a given page, currently missed by tlb_flush_page*.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201016210754.818257-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The SYS_timer is not directly wired to the ARM core, but to the
SoC (peripheral) interrupt controller.
Fixes: 0e5bbd74064 ("hw/arm/bcm2835_peripherals: Use the SYS_timer")
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
While APEI is a generic ACPI feature (usable by X86 and ARM64), only
the 'virt' machine uses it, by enabling the RAS Virtualization. See
commit 2afa8c8519: "hw/arm/virt: Introduce a RAS machine option").
Restrict the APEI tables generation code to the single user: the virt
machine. If another machine wants to use it, it simply has to 'select
ACPI_APEI' in its Kconfig.
Fixes: aa16508f1d ("ACPI: Build related register address fields via hardware error fw_cfg blob")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201008161414.2672569-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The time to transmit a char is expressed in nanoseconds, not in ticks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201014213601.205222-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
For AArch32, unlike the VCVT of integer to float, which honours the
rounding mode specified by the FPSCR, VCVT of fixed-point to float is
always round-to-nearest. (AArch64 fixed-point-to-float conversions
always honour the FPCR rounding mode.)
Implement this by providing _round_to_nearest versions of the
relevant helpers which set the rounding mode temporarily when making
the call to the underlying softfloat function.
We only need to change the VFP VCVT instructions, because the
standard- FPSCR value used by the Neon VCVT is always set to
round-to-nearest, so we don't need to do the extra work of saving
and restoring the rounding mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201013103532.13391-1-peter.maydell@linaro.org
|
|
The SMLAD instruction is supposed to:
* signed multiply Rn[15:0] * Rm[15:0]
* signed multiply Rn[31:16] * Rm[31:16]
* perform a signed addition of the products and Ra
* set Rd to the low 32 bits of the theoretical
infinite-precision result
* set the Q flag if the sign-extension of Rd
would differ from the infinite-precision result
(ie on overflow)
Our current implementation doesn't quite do this, though: it performs
an addition of the products setting Q on overflow, and then it adds
Ra, again possibly setting Q. This sometimes incorrectly sets Q when
the architecturally mandated only-check-for-overflow-once algorithm
does not. For instance:
r1 = 0x80008000; r2 = 0x80008000; r3 = 0xffffffff
smlad r0, r1, r2, r3
This is (-32768 * -32768) + (-32768 * -32768) - 1
The products are both 0x4000_0000, so when added together as 32-bit
signed numbers they overflow (and QEMU sets Q), but because the
addition of Ra == -1 brings the total back down to 0x7fff_ffff
there is no overflow for the complete operation and setting Q is
incorrect.
Fix this edge case by resorting to 64-bit arithmetic for the
case where we need to add three values together.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201009144712.11187-1-peter.maydell@linaro.org
|
|
xen-save-devices-state doesn't currently generate a vmdesc, so restore
always triggers "Expected vmdescription section, but got 0". This is
not a problem when restore comes from a file. However, when QEMU runs
in a linux stubdom and comes over a console, EOF is not received. This
causes a delay restoring - though it does restore.
Setting suppress-vmdesc skips looking for the vmdesc during restore and
avoids the wait.
The other approach would be generate a vmdesc in qemu_save_device_state.
Since COLO shared that function, and the vmdesc is just discarded on
restore, we choose to skip it.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201013190506.3325-1-jandryuk@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Currently a single watch on /local/domain/X/backend is registered by each
QEMU process running in service domain X (where X is usually 0). The purpose
of this watch is to ensure that QEMU is notified when the Xen toolstack
creates a new device backend area.
Such a backend area is specific to a single frontend area created for a
specific guest domain and, since each QEMU process is also created to service
a specfic guest domain, it is unnecessary and inefficient to notify all QEMU
processes.
Only the QEMU process associated with the same guest domain need
receive the notification. This patch re-factors the watch registration code
such that notifications are targetted appropriately.
Reported-by: Jerome Leseinne <jerome.leseinne@gmail.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201001081500.1026-1-paul@xen.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200902224311.1321159-58-ehabkost@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
There's no references in only file which includes xenguest.h
to any xen definitions. And there's no references to -lxenguest
in qemu, either. Drop it.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200727140048.19779-1-mjt@msgid.tls.msk.ru>
[perard: rebased]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
This test case uses the 9pfs 'local' driver to create a directory
and then checks if the expected directory was actually created
(as real directory) on host side.
This patch introduces a custom split() implementation, because
the test code requires non empty array elements as result. For
that reason g_strsplit() would not be a good alternative, as
it would require additional filter code for reshuffling the
array, and the resulting code would be even more complex than
this split() function.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <be342f236842272275f65dbe05587f0a5409ad77.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|
|
This new public function virtio_9p_test_path() allows 9pfs
'local' tests to translate a path from guest scope to host
scope. For instance by passing an empty string it would
return the root path on host of the exported 9pfs tree.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <b563d3c73c6391ec927a2622c9f65c09ca56bd83.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|
|
Before running the first 9pfs test case, make sure the test directory
for running the 9pfs 'local' tests on is entirely empty. For that
reason simply delete the test directory (if any) before (re)creating
it on test suite startup.
Note: The preferable precise behaviour would be the test directory
only being wiped once *before* a test suite run. Right now the test
directory is also wiped at the *end* of a test suite run because
libqos is calling the virtio_9p_register_nodes() callback for some
reason also when a test suite completed. This is suboptimal as
developers cannot immediately see what files and directories the
9pfs local tests created precisely after the test suite completed.
But fortunately the test directory is not wiped if some test failed.
So it is probably not worth it drilling another hole into libqos
for this issue.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <b30776ea3289dc40dabc7d0063d825d21d9a65bf.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|
|
This patch introduces 9pfs test cases using the 9pfs 'local'
filesystem driver which reads/writes/creates/deletes real files
and directories.
In this initial version, there is only one local test which actually
only checks if the 9pfs 'local' device was created successfully.
Before the 9pfs 'local' tests are run, a test directory 'qtest-9p-local'
is created (with world rwx permissions) under the current working
directory. At this point that test directory is not auto deleted yet.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <81fc4b3b6b6c9bf7999e79f5e7cbc364a5f09ddb.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|
|
All existing 9pfs test cases are using the 'synth' fs driver so far, which
means they are not accessing real files, but a purely simulated (in RAM
only) file system.
Let's make this clear by changing the prefix of the individual qtest case
names from 'fs/' to 'synth/'. That way they'll be easily distinguishable
from upcoming new 9pfs test cases supposed to be using a different fs
driver.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <e04e75acb849b085c6d6320b2433a15fa935bcff.1602182956.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|
|
Don't trigger any performance warning if we're just running test cases,
because tests intentionally run for edge cases.
So far performance warnings were suppressed for the 'synth' fs driver
backend only. This patch suppresses them for all 9p fs driver backends.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <a2d2ff2163f8853ea782a7a1d4e6f2afd7c29ffe.1603106145.git.qemu_oss@crudebyte.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
|