| Commit message (Collapse) | Author | Files | Lines |
|---|
|
The AT instruction is UNDEFINED if the {NSE,NS} configuration is
invalid. Add a function to check this on all AT instructions that apply
to an EL lower than 3.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230809123706.1842548-6-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
|
|
At the moment we only handle Secure and Nonsecure security spaces for
the AT instructions. Add support for Realm and Root.
For AArch64, arm_security_space() gives the desired space. ARM DDI0487J
says (R_NYXTL):
If EL3 is implemented, then when an address translation instruction
that applies to an Exception level lower than EL3 is executed, the
Effective value of SCR_EL3.{NSE, NS} determines the target Security
state that the instruction applies to.
For AArch32, some instructions can access NonSecure space from Secure,
so we still need to pass the state explicitly to do_ats_write().
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230809123706.1842548-5-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
GPC checks are not performed on the output address for AT instructions,
as stated by ARM DDI 0487J in D8.12.2:
When populating PAR_EL1 with the result of an address translation
instruction, granule protection checks are not performed on the final
output address of a successful translation.
Rename get_phys_addr_with_secure(), since it's only used to handle AT
instructions.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230809123706.1842548-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
When HCR_EL2.E2H is enabled, TLB entries are formed using the EL2&0
translation regime, instead of the EL2 translation regime. The TLB VAE2*
instructions invalidate the regime that corresponds to the current value
of HCR_EL2.E2H.
At the moment we only invalidate the EL2 translation regime. This causes
problems with RMM, which issues TLBI VAE2IS instructions with
HCR_EL2.E2H enabled. Update vae2_tlbmask() to take HCR_EL2.E2H into
account.
Add vae2_tlbbits() as well, since the top-byte-ignore configuration is
different between the EL2&0 and EL2 regime.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230809123706.1842548-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
In realm state, stage-2 translation tables are fetched from the realm
physical address space (R_PGRQD).
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230809123706.1842548-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The PAR_EL1.SH field documents that for the cases of:
* Device memory
* Normal memory with both Inner and Outer Non-Cacheable
the field should be 0b10 rather than whatever was in the
translation table descriptor field. (In the pseudocode this
is handled by PAREncodeShareability().) Perform this
adjustment when assembling a PAR value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-16-peter.maydell@linaro.org
|
|
When we report faults due to stage 2 faults during a stage 1
page table walk, the 'level' parameter should be the level
of the walk in stage 2 that faulted, not the level of the
walk in stage 1. Correct the reporting of these faults.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-15-peter.maydell@linaro.org
|
|
The architecture doesn't permit block descriptors at any arbitrary
level of the page table walk; it depends on the granule size which
levels are permitted. We implemented only a partial version of this
check which assumes that block descriptors are valid at all levels
except level 3, which meant that we wouldn't deliver the Translation
fault for all cases of this sort of guest page table error.
Implement the logic corresponding to the pseudocode
AArch64.DecodeDescriptorType() and AArch64.BlockDescSupported().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-14-peter.maydell@linaro.org
|
|
When the MMU is disabled, data accesses should be Device nGnRnE,
Outer Shareable, Untagged. We handle the other cases from
AArch64.S1DisabledOutput() correctly but missed this one.
Device nGnRnE is memattr == 0, so the only part we were missing
was that shareability should be set to 2 for both insn fetches
and data accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-13-peter.maydell@linaro.org
|
|
We only use S1Translate::out_secure in two places, where we are
setting up MemTxAttrs for a page table load. We can use
arm_space_is_secure(ptw->out_space) instead, which guarantees
that we're setting the MemTxAttrs secure and space fields
consistently, and allows us to drop the out_secure field in
S1Translate entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-12-peter.maydell@linaro.org
|
|
We no longer look at the in_secure field of the S1Translate struct
anyway, so we can remove it and all the code which sets it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-11-peter.maydell@linaro.org
|
|
Replace the last uses of ptw->in_secure with appropriate
checks on ptw->in_space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-10-peter.maydell@linaro.org
|
|
When we do a translation in Secure state, the NSTable bits in table
descriptors may downgrade us to NonSecure; we update ptw->in_secure
and ptw->in_space accordingly. We guard that check correctly with a
conditional that means it's only applied for Secure stage 1
translations. However, later on in get_phys_addr_lpae() we fold the
effects of the NSTable bits into the final descriptor attributes
bits, and there we do it unconditionally regardless of the CPU state.
That means that in Realm state (where in_secure is false) we will set
bit 5 in attrs, and later use it to decide to output to non-secure
space.
We don't in fact need to do this folding in at all any more (since
commit 2f1ff4e7b9f30c): if an NSTable bit was set then we have
already set ptw->in_space to ARMSS_NonSecure, and in that situation
we don't look at attrs bit 5. The only thing we still need to deal
with is the real NS bit in the final descriptor word, so we can just
drop the code that ORed in the NSTable bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-9-peter.maydell@linaro.org
|
|
Pass an ARMSecuritySpace instead of a bool secure to
arm_is_el2_enabled_secstate(). This doesn't change behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-8-peter.maydell@linaro.org
|
|
arm_hcr_el2_eff_secstate() takes a bool secure, which it uses to
determine whether EL2 is enabled in the current security state.
With the advent of FEAT_RME this is no longer sufficient, because
EL2 can be enabled for Secure state but not for Root, and both
of those will pass 'secure == true' in the callsites in ptw.c.
As it happens in all of our callsites in ptw.c we either avoid making
the call or else avoid using the returned value if we're doing a
translation for Root, so this is not a behaviour change even if the
experimental FEAT_RME is enabled. But it is less confusing in the
ptw.c code if we avoid the use of a bool secure that duplicates some
of the information in the ArmSecuritySpace argument.
Make arm_hcr_el2_eff_secstate() take an ARMSecuritySpace argument
instead. Because we always want to know the HCR_EL2 for the
security state defined by the current effective value of
SCR_EL3.{NSE,NS}, it makes no sense to pass ARMSS_Root here,
and we assert that callers don't do that.
To avoid the assert(), we thus push the call to
arm_hcr_el2_eff_secstate() down into the cases in
regime_translation_disabled() that need it, rather than calling the
function and ignoring the result for the Root space translations.
All other calls to this function in ptw.c are already in places
where we have confirmed that the mmu_idx is a stage 2 translation
or that the regime EL is not 3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-7-peter.maydell@linaro.org
|
|
Plumb the ARMSecurityState through to regime_translation_disabled()
rather than just a bool is_secure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-6-peter.maydell@linaro.org
|
|
In commit 6d2654ffacea813916176 we created the S1Translate struct and
used it to plumb through various arguments that we were previously
passing one-at-a-time to get_phys_addr_v5(), get_phys_addr_v6(), and
get_phys_addr_lpae(). Extend that pattern to get_phys_addr_pmsav5(),
get_phys_addr_pmsav7(), get_phys_addr_pmsav8() and
get_phys_addr_disabled(), so that all the get_phys_addr_* functions
we call from get_phys_addr_nogpc() take the S1Translate struct rather
than the mmu_idx and is_secure bool.
(This refactoring is a prelude to having the called functions look
at ptw->is_space rather than using an is_secure boolean.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-5-peter.maydell@linaro.org
|
|
The s1ns bit in ARMMMUFaultInfo is documented as "true if
we faulted on a non-secure IPA while in secure state". Both the
places which look at this bit only do so after having confirmed
that this is a stage 2 fault and we're dealing with Secure EL2,
which leaves the ptw.c code free to set the bit to any random
value in the other cases.
Instead of taking advantage of that freedom, consistently
make the bit be set to false for the "not a stage 2 fault
for Secure EL2" cases. This removes some cases where we
were using an 'is_secure' boolean and leaving the reader
guessing about whether that was the right thing for Realm
and Root cases.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-4-peter.maydell@linaro.org
|
|
In S1_ptw_translate() we set up the ARMMMUFaultInfo if the attempt to
translate the page descriptor address into a physical address fails.
This used to only be possible if we are doing a stage 2 ptw for that
descriptor address, and so the code always sets fi->stage2 and
fi->s1ptw to true. However, with FEAT_RME it is also possible for
the lookup of the page descriptor address to fail because of a
Granule Protection Check fault. These should not be reported as
stage 2, otherwise arm_deliver_fault() will incorrectly set
HPFAR_EL2. Similarly the s1ptw bit should only be set for stage 2
faults on stage 1 translation table walks, i.e. not for GPC faults.
Add a comment to the the other place where we might detect a
stage2-fault-on-stage-1-ptw, in arm_casq_ptw(), noting why we know in
that case that it must really be a stage 2 fault and not a GPC fault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-3-peter.maydell@linaro.org
|
|
For an Unsupported Atomic Update fault where the stage 1 translation
table descriptor update can't be done because it's to an unsupported
memory type, this is a stage 1 abort (per the Arm ARM R_VSXXT). This
means we should not set fi->s1ptw, because this will cause the code
in the get_phys_addr_lpae() error-exit path to mark it as stage 2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807141514.19075-2-peter.maydell@linaro.org
|
|
The returned value was always zero and had no meaning.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-7-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
An error may occur after s->as is allocated, for example if the
KVM_CREATE_VM ioctl call fails.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-6-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
On MIPS, kvm_arch_get_default_type() returns a negative value when an
error occurred so handle the case. Also, let other machines return
negative values when errors occur and declare returning a negative
value as the correct way to propagate an error that happened when
determining KVM type.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-5-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
On MIPS, QEMU requires KVM_VM_MIPS_VZ type for KVM. Report an error in
such a case as other architectures do when an error occurred during KVM
type decision.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-4-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
Before this change, the default KVM type, which is used for non-virt
machine models, was 0.
The kernel documentation says:
> On arm64, the physical address size for a VM (IPA Size limit) is
> limited to 40bits by default. The limit can be configured if the host
> supports the extension KVM_CAP_ARM_VM_IPA_SIZE. When supported, use
> KVM_VM_TYPE_ARM_IPA_SIZE(IPA_Bits) to set the size in the machine type
> identifier, where IPA_Bits is the maximum width of any physical
> address used by the VM. The IPA_Bits is encoded in bits[7-0] of the
> machine type identifier.
>
> e.g, to configure a guest to use 48bit physical address size::
>
> vm_fd = ioctl(dev_fd, KVM_CREATE_VM, KVM_VM_TYPE_ARM_IPA_SIZE(48));
>
> The requested size (IPA_Bits) must be:
>
> == =========================================================
> 0 Implies default size, 40bits (for backward compatibility)
> N Implies N bits, where N is a positive integer such that,
> 32 <= N <= Host_IPA_Limit
> == =========================================================
> Host_IPA_Limit is the maximum possible value for IPA_Bits on the host
> and is dependent on the CPU capability and the kernel configuration.
> The limit can be retrieved using KVM_CAP_ARM_VM_IPA_SIZE of the
> KVM_CHECK_EXTENSION ioctl() at run-time.
>
> Creation of the VM will fail if the requested IPA size (whether it is
> implicit or explicit) is unsupported on the host.
https://docs.kernel.org/virt/kvm/api.html#kvm-create-vm
So if Host_IPA_Limit < 40, specifying 0 as the type will fail. This
actually confused libvirt, which uses "none" machine model to probe the
KVM availability, on M2 MacBook Air.
Fix this by using Host_IPA_Limit as the default type when
KVM_CAP_ARM_VM_IPA_SIZE is available.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-3-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
kvm_arch_get_default_type() returns the default KVM type. This hook is
particularly useful to derive a KVM type that is valid for "none"
machine model, which is used by libvirt to probe the availability of
KVM.
For MIPS, the existing mips_kvm_type() is reused. This function ensures
the availability of VZ which is mandatory to use KVM on the current
QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-2-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added doc comment for new function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
Exercise the DETECT mechanism of the GPIO peripheral.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-7-chris@laplante.io
[PMM: fixed coding style nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This is much better than just silently failing with OK.
Signed-off-by: Chris Laplante <chris@laplante.io>
Message-id: 20230728160324.1159090-6-chris@laplante.io
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Named interception of in-GPIOs is not supported yet.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-5-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Adds qtest_irq_intercept_out_named method, which utilizes a new optional
name parameter to the irq_intercept_out qtest command.
Signed-off-by: Chris Laplante <chris@laplante.io>
Message-id: 20230728160324.1159090-4-chris@laplante.io
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-3-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Implement nRF51 DETECT signal in the GPIO peripheral.
The reference manual makes mention of a per-pin DETECT signal, but these
are not exposed to the user. See https://devzone.nordicsemi.com/f/nordic-q-a/39858/gpio-per-pin-detect-signal-available
for more information. Currently, I don't see a reason to model these.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-2-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Missing the segment prefix means that user-only fails
to add guest_base for some 128-bit load/store.
Fixes: 098d0fc10d2 ("tcg/i386: Support 128-bit load/store")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1763
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
The 'aclint' property is being conditioned with tcg acceleration in
virt_machine_class_init(). But acceleration code starts later than the
class init of the board, meaning that tcg_enabled() will be always be
false during class_init(), and the option is never being declared even
when declaring TCG accel:
$ ./build/qemu-system-riscv64 -M virt,accel=tcg,aclint=on
qemu-system-riscv64: Property 'virt-machine.aclint' not found
Fix it by moving the check from class_init() to machine_init(). Tune the
description to mention that the option is TCG only.
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Fixes: c0716c81b ("hw/riscv/virt: Restrict ACLINT to TCG")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1823
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230811160224.440697-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
cpu->cfg.mvendorid is a 32 bit field and kvm_set_one_reg() always write
a target_ulong val, i.e. a 64 bit field in a 64 bit host.
Given that we're passing a pointer to the mvendorid field, the reg is
reading 64 bits starting from mvendorid and going 32 bits in the next
field, marchid. Here's an example:
$ ./qemu-system-riscv64 -machine virt,accel=kvm -m 2G -smp 1 \
-cpu rv64,marchid=0xab,mvendorid=0xcd,mimpid=0xef(...)
(inside the guest)
# cat /proc/cpuinfo
processor : 0
hart : 0
isa : rv64imafdc_zicbom_zicboz_zihintpause_zbb_sstc
mmu : sv57
mvendorid : 0xab000000cd
marchid : 0xab
mimpid : 0xef
'mvendorid' was written as a combination of 0xab (the value from the
adjacent field, marchid) and its intended value 0xcd.
Fix it by assigning cpu->cfg.mvendorid to a target_ulong var 'reg' and
use it as input for kvm_set_one_reg(). Here's the result with this patch
applied and using the same QEMU command line:
# cat /proc/cpuinfo
processor : 0
hart : 0
isa : rv64imafdc_zicbom_zicboz_zihintpause_zbb_sstc
mmu : sv57
mvendorid : 0xcd
marchid : 0xab
mimpid : 0xef
This bug affects only the generic (rv64) CPUs when running with KVM in a
64 bit env since the 'host' CPU does not allow the machine IDs to be
changed via command line.
Fixes: 1fb5a622f7 ("target/riscv: handle mvendorid/marchid/mimpid for KVM CPUs")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230802180058.281385-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
The PCI_COMMAND register is located at offset 4 within
the PCI configuration space and occupies 2 bytes. The
interrupt disable bit is at the 10th bit, which corresponds
to the byte at offset 5 in the PCI configuration space.
In our testing environment, the guest driver may directly
updates the byte at offset 5 in the PCI configuration space.
The backtrace looks like as following:
at hw/pci/pci.c:1442
at hw/virtio/virtio-pci.c:605
val=5, len=1) at hw/pci/pci_host.c:81
In this situation, the range_covers_byte function called
by the pci_default_write_config function will return false,
resulting in the inability to handle the interrupt disable
update event.
To fix this issue, we can use the ranges_overlap function
instead of range_covers_byte to determine whether the interrupt
bit has been updated.
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Signed-off-by: yuanminghao <yuanmh12@chinatelecom.cn>
Message-Id: <ce2d0437-8faa-4d61-b536-4668f645a959@chinatelecom.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: b6981cb57be5 ("pci: interrupt disable bit support")
|
|
In pcie_bus_realize(), a root bus is realized as a PCIe bus and a non-root
bus is realized as a PCIe bus if its parent bus is a PCIe bus. However,
the child bus "dw-pcie" is realized before the parent bus "pcie" which is
the root PCIe bus. Thus, the extended configuration space is not accessible
on "dw-pcie". The issue can be resolved by adding the
PCI_BUS_EXTENDED_CONFIG_SPACE flag to "pcie" before "dw-pcie" is realized.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Message-Id: <20230809102257.25121-1-jason.chien@sifive.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Signed-off-by: Jason Chien <<a href="mailto:jason.chien@sifive.com" target="_blank">jason.chien@sifive.com</a>><br>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
When starting a remote connection GDB sends an '+':
/* Ack any packet which the remote side has already sent. */
remote_serial_write ("+", 1);
which gets flagged as a garbage character in the gdbstub state
machine. As gdb does send it out lets be permissive about the handling
so we can better see real issues.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: gdb-patches@sourceware.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230810153640.1879717-9-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
The original fix caused problems with spurious characters on other
system emulation. So:
- instead of spamming output make the warning a trace point
- ensure we only allow a stop reply if it was 0x3
Suggested-by: Matheus Tavares Bernardino <quic_mathbern@quicinc.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <456ed3318421dd7946bdfb5ceda7e05332da368c.1690910333.git.quic_mathbern@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230810153640.1879717-8-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Without -S we run into potential races with tests starting before the
gdbstub attaches. We don't need to worry about user-mode as enabling
the gdbstub implies we wait for the initial connection.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230810153640.1879717-7-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
When load_atom_extract_al16_or_al8 is inexpensive, we want to use
it early, in order to avoid the overhead of required_atomicity.
However, we must not read past the end of the page.
If there are more than 8 bytes remaining, then both the "aligned 16"
and "aligned 8" paths align down so that the read has at least
16 bytes remaining on the page.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
In qemu we catch accesses to files like /proc/cpuinfo or /proc/net/route
and return to the guest contents which would be visible on a real system
(instead what the host would show).
This patch fixes a bug, where for example the accesses
cat /proc////cpuinfo
or
cd /proc && cat cpuinfo
will not be recognized by qemu and where qemu will wrongly show
the contents of the host's /proc/cpuinfo file.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230803214450.647040-2-deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Fix a crash in qemu-user when running
cat /proc/self/maps
in a chroot, where /proc isn't mounted.
The problem was introduced by commit 3ce3dd8ca965 ("util/selfmap:
Rewrite using qemu/interval-tree.h") where in open_self_maps_1() the
function read_self_maps() is called and which returns NULL if it can't
read the hosts /proc/self/maps file. Afterwards that NULL is fed into
interval_tree_iter_first() which doesn't check if the root node is NULL.
Fix it by adding a check if root is NULL and return NULL in that case.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 3ce3dd8ca965 ("util/selfmap: Rewrite using qemu/interval-tree.h")
Message-Id: <ZNOsq6Z7t/eyIG/9@p100>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
This test fails when host page size != guest page size,
because qemu may not be able to directly map the file.
Fixes: a6341482695 ("tests/tcg: Add a test for info proc mappings")
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Rather than using a zero tuple to end the table, use a macro
to apply ARRAY_SIZE and pass that on to the convert functions.
This fixes two bugs in which the conversion functions required
that both the target and host masks be non-zero in order to
continue, rather than require both target and host masks be
zero in order to terminate.
This affected mmap_flags_tbl when the host does not support
all of the flags we wish to convert (e.g. MAP_UNINITIALIZED).
Mapping these flags to zero is good enough, and matches how
the kernel ignores bits that are unknown.
Fixes: 4b840f96 ("linux-user: Populate more bits in mmap_flags_tbl")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
New function that rejects unsupported map types and flags.
In 4b840f96 we should not have accepted MAP_SHARED_VALIDATE
without actually validating the rest of the flags.
Fixes: 4b840f96 ("linux-user: Populate more bits in mmap_flags_tbl")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|