| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Exposing SYSCFG inputs to the SoC is practical in order to wire the SoC
to the optional DM163 display from the board code (GPIOs outputs need
to be connected to both SYSCFG inputs and DM163 inputs).
STM32L4x5 SYSCFG in-irq interception needed to be changed accordingly.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240424200929.240921-3-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The test mangles the GPIO address and the pin number in the
qtest_add_data_func data parameter. Doing so, it assumes that the host
pointer size is always 64-bit, which breaks on 32-bit :
../tests/qtest/stm32l4x5_gpio-test.c: In function ‘test_gpio_output_mode’:
../tests/qtest/stm32l4x5_gpio-test.c:272:25: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
272 | unsigned int pin = ((uint64_t)data) & 0xF;
| ^
../tests/qtest/stm32l4x5_gpio-test.c:273:22: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
273 | uint32_t gpio = ((uint64_t)data) >> 32;
| ^
To fix, improve the mangling of the GPIO address and pin number fields
by using GPIO_SIZE so that the resulting value fits in a 32-bit pointer.
While at it, include some helpers to hide the details.
Cc: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Cc: Inès Varhol <ines.varhol@telecom-paris.fr>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-id: 20240329092747.298259-1-clg@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
|
The testcase contains :
- `test_idr_reset_value()` :
Checks the reset values of MODER, OTYPER, PUPDR, ODR and IDR.
- `test_gpio_output_mode()` :
Checks that writing a bit in register ODR results in the corresponding
pin rising or lowering, if this pin is configured in output mode.
- `test_gpio_input_mode()` :
Checks that a input pin set high or low externally results
in the pin rising and lowering.
- `test_pull_up_pull_down()` :
Checks that a floating pin in pull-up/down mode is actually high/down.
- `test_push_pull()` :
Checks that a pin set externally is disconnected when configured in
push-pull output mode, and can't be set externally while in this mode.
- `test_open_drain()` :
Checks that a pin set externally high is disconnected when configured
in open-drain output mode, and can't be set high while in this mode.
- `test_bsrr_brr()` :
Checks that writing to BSRR and BRR has the desired result in ODR.
- `test_clock_enable()` :
Checks that GPIO clock is at the right frequency after enabling it.
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240305210444.310665-4-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|