hw: move target-independent files to subdirectories

This patch tackles all files that are compiled once, moving
them to subdirectories of hw/.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

4 files changed, 693 insertions, 0 deletions

diff --git a/hw/gpio/Makefile.objs b/hw/gpio/Makefile.objs
index e69de29bb2..f8d8ee87f9 100644
--- a/hw/gpio/Makefile.objs
+++ b/hw/gpio/Makefile.objs
@@ -0,0 +1,3 @@
+common-obj-$(CONFIG_MAX7310) += max7310.o
+common-obj-$(CONFIG_PL061) += pl061.o
+common-obj-$(CONFIG_PUV3) += puv3_gpio.o
diff --git a/hw/gpio/max7310.c b/hw/gpio/max7310.c
new file mode 100644
index 0000000000..59b287703e
--- /dev/null
+++ b/hw/gpio/max7310.c
@@ -0,0 +1,213 @@
+/*
+ * MAX7310 8-port GPIO expansion chip.
+ *
+ * Copyright (c) 2006 Openedhand Ltd.
+ * Written by Andrzej Zaborowski <balrog@zabor.org>
+ *
+ * This file is licensed under GNU GPL.
+ */
+
+#include "hw/i2c/i2c.h"
+
+typedef struct {
+    I2CSlave i2c;
+    int i2c_command_byte;
+    int len;
+
+    uint8_t level;
+    uint8_t direction;
+    uint8_t polarity;
+    uint8_t status;
+    uint8_t command;
+    qemu_irq handler[8];
+    qemu_irq *gpio_in;
+} MAX7310State;
+
+static void max7310_reset(DeviceState *dev)
+{
+    MAX7310State *s = FROM_I2C_SLAVE(MAX7310State, I2C_SLAVE(dev));
+    s->level &= s->direction;
+    s->direction = 0xff;
+    s->polarity = 0xf0;
+    s->status = 0x01;
+    s->command = 0x00;
+}
+
+static int max7310_rx(I2CSlave *i2c)
+{
+    MAX7310State *s = (MAX7310State *) i2c;
+
+    switch (s->command) {
+    case 0x00:	/* Input port */
+        return s->level ^ s->polarity;
+        break;
+
+    case 0x01:	/* Output port */
+        return s->level & ~s->direction;
+        break;
+
+    case 0x02:	/* Polarity inversion */
+        return s->polarity;
+
+    case 0x03:	/* Configuration */
+        return s->direction;
+
+    case 0x04:	/* Timeout */
+        return s->status;
+        break;
+
+    case 0xff:	/* Reserved */
+        return 0xff;
+
+    default:
+#ifdef VERBOSE
+        printf("%s: unknown register %02x\n", __FUNCTION__, s->command);
+#endif
+        break;
+    }
+    return 0xff;
+}
+
+static int max7310_tx(I2CSlave *i2c, uint8_t data)
+{
+    MAX7310State *s = (MAX7310State *) i2c;
+    uint8_t diff;
+    int line;
+
+    if (s->len ++ > 1) {
+#ifdef VERBOSE
+        printf("%s: message too long (%i bytes)\n", __FUNCTION__, s->len);
+#endif
+        return 1;
+    }
+
+    if (s->i2c_command_byte) {
+        s->command = data;
+        s->i2c_command_byte = 0;
+        return 0;
+    }
+
+    switch (s->command) {
+    case 0x01:	/* Output port */
+        for (diff = (data ^ s->level) & ~s->direction; diff;
+                        diff &= ~(1 << line)) {
+            line = ffs(diff) - 1;
+            if (s->handler[line])
+                qemu_set_irq(s->handler[line], (data >> line) & 1);
+        }
+        s->level = (s->level & s->direction) | (data & ~s->direction);
+        break;
+
+    case 0x02:	/* Polarity inversion */
+        s->polarity = data;
+        break;
+
+    case 0x03:	/* Configuration */
+        s->level &= ~(s->direction ^ data);
+        s->direction = data;
+        break;
+
+    case 0x04:	/* Timeout */
+        s->status = data;
+        break;
+
+    case 0x00:	/* Input port - ignore writes */
+	break;
+    default:
+#ifdef VERBOSE
+        printf("%s: unknown register %02x\n", __FUNCTION__, s->command);
+#endif
+        return 1;
+    }
+
+    return 0;
+}
+
+static void max7310_event(I2CSlave *i2c, enum i2c_event event)
+{
+    MAX7310State *s = (MAX7310State *) i2c;
+    s->len = 0;
+
+    switch (event) {
+    case I2C_START_SEND:
+        s->i2c_command_byte = 1;
+        break;
+    case I2C_FINISH:
+#ifdef VERBOSE
+        if (s->len == 1)
+            printf("%s: message too short (%i bytes)\n", __FUNCTION__, s->len);
+#endif
+        break;
+    default:
+        break;
+    }
+}
+
+static const VMStateDescription vmstate_max7310 = {
+    .name = "max7310",
+    .version_id = 0,
+    .minimum_version_id = 0,
+    .minimum_version_id_old = 0,
+    .fields      = (VMStateField []) {
+        VMSTATE_INT32(i2c_command_byte, MAX7310State),
+        VMSTATE_INT32(len, MAX7310State),
+        VMSTATE_UINT8(level, MAX7310State),
+        VMSTATE_UINT8(direction, MAX7310State),
+        VMSTATE_UINT8(polarity, MAX7310State),
+        VMSTATE_UINT8(status, MAX7310State),
+        VMSTATE_UINT8(command, MAX7310State),
+        VMSTATE_I2C_SLAVE(i2c, MAX7310State),
+        VMSTATE_END_OF_LIST()
+    }
+};
+
+static void max7310_gpio_set(void *opaque, int line, int level)
+{
+    MAX7310State *s = (MAX7310State *) opaque;
+    if (line >= ARRAY_SIZE(s->handler) || line  < 0)
+        hw_error("bad GPIO line");
+
+    if (level)
+        s->level |= s->direction & (1 << line);
+    else
+        s->level &= ~(s->direction & (1 << line));
+}
+
+/* MAX7310 is SMBus-compatible (can be used with only SMBus protocols),
+ * but also accepts sequences that are not SMBus so return an I2C device.  */
+static int max7310_init(I2CSlave *i2c)
+{
+    MAX7310State *s = FROM_I2C_SLAVE(MAX7310State, i2c);
+
+    qdev_init_gpio_in(&i2c->qdev, max7310_gpio_set, 8);
+    qdev_init_gpio_out(&i2c->qdev, s->handler, 8);
+
+    return 0;
+}
+
+static void max7310_class_init(ObjectClass *klass, void *data)
+{
+    DeviceClass *dc = DEVICE_CLASS(klass);
+    I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
+
+    k->init = max7310_init;
+    k->event = max7310_event;
+    k->recv = max7310_rx;
+    k->send = max7310_tx;
+    dc->reset = max7310_reset;
+    dc->vmsd = &vmstate_max7310;
+}
+
+static const TypeInfo max7310_info = {
+    .name          = "max7310",
+    .parent        = TYPE_I2C_SLAVE,
+    .instance_size = sizeof(MAX7310State),
+    .class_init    = max7310_class_init,
+};
+
+static void max7310_register_types(void)
+{
+    type_register_static(&max7310_info);
+}
+
+type_init(max7310_register_types)
diff --git a/hw/gpio/pl061.c b/hw/gpio/pl061.c
new file mode 100644
index 0000000000..74bc109488
--- /dev/null
+++ b/hw/gpio/pl061.c
@@ -0,0 +1,336 @@
+/*
+ * Arm PrimeCell PL061 General Purpose IO with additional
+ * Luminary Micro Stellaris bits.
+ *
+ * Copyright (c) 2007 CodeSourcery.
+ * Written by Paul Brook
+ *
+ * This code is licensed under the GPL.
+ */
+
+#include "hw/sysbus.h"
+
+//#define DEBUG_PL061 1
+
+#ifdef DEBUG_PL061
+#define DPRINTF(fmt, ...) \
+do { printf("pl061: " fmt , ## __VA_ARGS__); } while (0)
+#define BADF(fmt, ...) \
+do { fprintf(stderr, "pl061: error: " fmt , ## __VA_ARGS__); exit(1);} while (0)
+#else
+#define DPRINTF(fmt, ...) do {} while(0)
+#define BADF(fmt, ...) \
+do { fprintf(stderr, "pl061: error: " fmt , ## __VA_ARGS__);} while (0)
+#endif
+
+static const uint8_t pl061_id[12] =
+  { 0x00, 0x00, 0x00, 0x00, 0x61, 0x10, 0x04, 0x00, 0x0d, 0xf0, 0x05, 0xb1 };
+static const uint8_t pl061_id_luminary[12] =
+  { 0x00, 0x00, 0x00, 0x00, 0x61, 0x00, 0x18, 0x01, 0x0d, 0xf0, 0x05, 0xb1 };
+
+typedef struct {
+    SysBusDevice busdev;
+    MemoryRegion iomem;
+    uint32_t locked;
+    uint32_t data;
+    uint32_t old_data;
+    uint32_t dir;
+    uint32_t isense;
+    uint32_t ibe;
+    uint32_t iev;
+    uint32_t im;
+    uint32_t istate;
+    uint32_t afsel;
+    uint32_t dr2r;
+    uint32_t dr4r;
+    uint32_t dr8r;
+    uint32_t odr;
+    uint32_t pur;
+    uint32_t pdr;
+    uint32_t slr;
+    uint32_t den;
+    uint32_t cr;
+    uint32_t float_high;
+    uint32_t amsel;
+    qemu_irq irq;
+    qemu_irq out[8];
+    const unsigned char *id;
+} pl061_state;
+
+static const VMStateDescription vmstate_pl061 = {
+    .name = "pl061",
+    .version_id = 2,
+    .minimum_version_id = 1,
+    .fields = (VMStateField[]) {
+        VMSTATE_UINT32(locked, pl061_state),
+        VMSTATE_UINT32(data, pl061_state),
+        VMSTATE_UINT32(old_data, pl061_state),
+        VMSTATE_UINT32(dir, pl061_state),
+        VMSTATE_UINT32(isense, pl061_state),
+        VMSTATE_UINT32(ibe, pl061_state),
+        VMSTATE_UINT32(iev, pl061_state),
+        VMSTATE_UINT32(im, pl061_state),
+        VMSTATE_UINT32(istate, pl061_state),
+        VMSTATE_UINT32(afsel, pl061_state),
+        VMSTATE_UINT32(dr2r, pl061_state),
+        VMSTATE_UINT32(dr4r, pl061_state),
+        VMSTATE_UINT32(dr8r, pl061_state),
+        VMSTATE_UINT32(odr, pl061_state),
+        VMSTATE_UINT32(pur, pl061_state),
+        VMSTATE_UINT32(pdr, pl061_state),
+        VMSTATE_UINT32(slr, pl061_state),
+        VMSTATE_UINT32(den, pl061_state),
+        VMSTATE_UINT32(cr, pl061_state),
+        VMSTATE_UINT32(float_high, pl061_state),
+        VMSTATE_UINT32_V(amsel, pl061_state, 2),
+        VMSTATE_END_OF_LIST()
+    }
+};
+
+static void pl061_update(pl061_state *s)
+{
+    uint8_t changed;
+    uint8_t mask;
+    uint8_t out;
+    int i;
+
+    /* Outputs float high.  */
+    /* FIXME: This is board dependent.  */
+    out = (s->data & s->dir) | ~s->dir;
+    changed = s->old_data ^ out;
+    if (!changed)
+        return;
+
+    s->old_data = out;
+    for (i = 0; i < 8; i++) {
+        mask = 1 << i;
+        if (changed & mask) {
+            DPRINTF("Set output %d = %d\n", i, (out & mask) != 0);
+            qemu_set_irq(s->out[i], (out & mask) != 0);
+        }
+    }
+
+    /* FIXME: Implement input interrupts.  */
+}
+
+static uint64_t pl061_read(void *opaque, hwaddr offset,
+                           unsigned size)
+{
+    pl061_state *s = (pl061_state *)opaque;
+
+    if (offset >= 0xfd0 && offset < 0x1000) {
+        return s->id[(offset - 0xfd0) >> 2];
+    }
+    if (offset < 0x400) {
+        return s->data & (offset >> 2);
+    }
+    switch (offset) {
+    case 0x400: /* Direction */
+        return s->dir;
+    case 0x404: /* Interrupt sense */
+        return s->isense;
+    case 0x408: /* Interrupt both edges */
+        return s->ibe;
+    case 0x40c: /* Interrupt event */
+        return s->iev;
+    case 0x410: /* Interrupt mask */
+        return s->im;
+    case 0x414: /* Raw interrupt status */
+        return s->istate;
+    case 0x418: /* Masked interrupt status */
+        return s->istate | s->im;
+    case 0x420: /* Alternate function select */
+        return s->afsel;
+    case 0x500: /* 2mA drive */
+        return s->dr2r;
+    case 0x504: /* 4mA drive */
+        return s->dr4r;
+    case 0x508: /* 8mA drive */
+        return s->dr8r;
+    case 0x50c: /* Open drain */
+        return s->odr;
+    case 0x510: /* Pull-up */
+        return s->pur;
+    case 0x514: /* Pull-down */
+        return s->pdr;
+    case 0x518: /* Slew rate control */
+        return s->slr;
+    case 0x51c: /* Digital enable */
+        return s->den;
+    case 0x520: /* Lock */
+        return s->locked;
+    case 0x524: /* Commit */
+        return s->cr;
+    case 0x528: /* Analog mode select */
+        return s->amsel;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR,
+                      "pl061_read: Bad offset %x\n", (int)offset);
+        return 0;
+    }
+}
+
+static void pl061_write(void *opaque, hwaddr offset,
+                        uint64_t value, unsigned size)
+{
+    pl061_state *s = (pl061_state *)opaque;
+    uint8_t mask;
+
+    if (offset < 0x400) {
+        mask = (offset >> 2) & s->dir;
+        s->data = (s->data & ~mask) | (value & mask);
+        pl061_update(s);
+        return;
+    }
+    switch (offset) {
+    case 0x400: /* Direction */
+        s->dir = value & 0xff;
+        break;
+    case 0x404: /* Interrupt sense */
+        s->isense = value & 0xff;
+        break;
+    case 0x408: /* Interrupt both edges */
+        s->ibe = value & 0xff;
+        break;
+    case 0x40c: /* Interrupt event */
+        s->iev = value & 0xff;
+        break;
+    case 0x410: /* Interrupt mask */
+        s->im = value & 0xff;
+        break;
+    case 0x41c: /* Interrupt clear */
+        s->istate &= ~value;
+        break;
+    case 0x420: /* Alternate function select */
+        mask = s->cr;
+        s->afsel = (s->afsel & ~mask) | (value & mask);
+        break;
+    case 0x500: /* 2mA drive */
+        s->dr2r = value & 0xff;
+        break;
+    case 0x504: /* 4mA drive */
+        s->dr4r = value & 0xff;
+        break;
+    case 0x508: /* 8mA drive */
+        s->dr8r = value & 0xff;
+        break;
+    case 0x50c: /* Open drain */
+        s->odr = value & 0xff;
+        break;
+    case 0x510: /* Pull-up */
+        s->pur = value & 0xff;
+        break;
+    case 0x514: /* Pull-down */
+        s->pdr = value & 0xff;
+        break;
+    case 0x518: /* Slew rate control */
+        s->slr = value & 0xff;
+        break;
+    case 0x51c: /* Digital enable */
+        s->den = value & 0xff;
+        break;
+    case 0x520: /* Lock */
+        s->locked = (value != 0xacce551);
+        break;
+    case 0x524: /* Commit */
+        if (!s->locked)
+            s->cr = value & 0xff;
+        break;
+    case 0x528:
+        s->amsel = value & 0xff;
+        break;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR,
+                      "pl061_write: Bad offset %x\n", (int)offset);
+    }
+    pl061_update(s);
+}
+
+static void pl061_reset(pl061_state *s)
+{
+  s->locked = 1;
+  s->cr = 0xff;
+}
+
+static void pl061_set_irq(void * opaque, int irq, int level)
+{
+    pl061_state *s = (pl061_state *)opaque;
+    uint8_t mask;
+
+    mask = 1 << irq;
+    if ((s->dir & mask) == 0) {
+        s->data &= ~mask;
+        if (level)
+            s->data |= mask;
+        pl061_update(s);
+    }
+}
+
+static const MemoryRegionOps pl061_ops = {
+    .read = pl061_read,
+    .write = pl061_write,
+    .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int pl061_init(SysBusDevice *dev, const unsigned char *id)
+{
+    pl061_state *s = FROM_SYSBUS(pl061_state, dev);
+    s->id = id;
+    memory_region_init_io(&s->iomem, &pl061_ops, s, "pl061", 0x1000);
+    sysbus_init_mmio(dev, &s->iomem);
+    sysbus_init_irq(dev, &s->irq);
+    qdev_init_gpio_in(&dev->qdev, pl061_set_irq, 8);
+    qdev_init_gpio_out(&dev->qdev, s->out, 8);
+    pl061_reset(s);
+    return 0;
+}
+
+static int pl061_init_luminary(SysBusDevice *dev)
+{
+    return pl061_init(dev, pl061_id_luminary);
+}
+
+static int pl061_init_arm(SysBusDevice *dev)
+{
+    return pl061_init(dev, pl061_id);
+}
+
+static void pl061_class_init(ObjectClass *klass, void *data)
+{
+    DeviceClass *dc = DEVICE_CLASS(klass);
+    SysBusDeviceClass *k = SYS_BUS_DEVICE_CLASS(klass);
+
+    k->init = pl061_init_arm;
+    dc->vmsd = &vmstate_pl061;
+}
+
+static const TypeInfo pl061_info = {
+    .name          = "pl061",
+    .parent        = TYPE_SYS_BUS_DEVICE,
+    .instance_size = sizeof(pl061_state),
+    .class_init    = pl061_class_init,
+};
+
+static void pl061_luminary_class_init(ObjectClass *klass, void *data)
+{
+    DeviceClass *dc = DEVICE_CLASS(klass);
+    SysBusDeviceClass *k = SYS_BUS_DEVICE_CLASS(klass);
+
+    k->init = pl061_init_luminary;
+    dc->vmsd = &vmstate_pl061;
+}
+
+static const TypeInfo pl061_luminary_info = {
+    .name          = "pl061_luminary",
+    .parent        = TYPE_SYS_BUS_DEVICE,
+    .instance_size = sizeof(pl061_state),
+    .class_init    = pl061_luminary_class_init,
+};
+
+static void pl061_register_types(void)
+{
+    type_register_static(&pl061_info);
+    type_register_static(&pl061_luminary_info);
+}
+
+type_init(pl061_register_types)
diff --git a/hw/gpio/puv3_gpio.c b/hw/gpio/puv3_gpio.c
new file mode 100644
index 0000000000..5bab97e95a
--- /dev/null
+++ b/hw/gpio/puv3_gpio.c
@@ -0,0 +1,141 @@
+/*
+ * GPIO device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "hw/hw.h"
+#include "hw/sysbus.h"
+
+#undef DEBUG_PUV3
+#include "hw/unicore32/puv3.h"
+
+typedef struct {
+    SysBusDevice busdev;
+    MemoryRegion iomem;
+    qemu_irq irq[9];
+
+    uint32_t reg_GPLR;
+    uint32_t reg_GPDR;
+    uint32_t reg_GPIR;
+} PUV3GPIOState;
+
+static uint64_t puv3_gpio_read(void *opaque, hwaddr offset,
+        unsigned size)
+{
+    PUV3GPIOState *s = opaque;
+    uint32_t ret = 0;
+
+    switch (offset) {
+    case 0x00:
+        ret = s->reg_GPLR;
+        break;
+    case 0x04:
+        ret = s->reg_GPDR;
+        break;
+    case 0x20:
+        ret = s->reg_GPIR;
+        break;
+    default:
+        DPRINTF("Bad offset 0x%x\n", offset);
+    }
+    DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+
+    return ret;
+}
+
+static void puv3_gpio_write(void *opaque, hwaddr offset,
+        uint64_t value, unsigned size)
+{
+    PUV3GPIOState *s = opaque;
+
+    DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+    switch (offset) {
+    case 0x04:
+        s->reg_GPDR = value;
+        break;
+    case 0x08:
+        if (s->reg_GPDR & value) {
+            s->reg_GPLR |= value;
+        } else {
+            DPRINTF("Write gpio input port error!");
+        }
+        break;
+    case 0x0c:
+        if (s->reg_GPDR & value) {
+            s->reg_GPLR &= ~value;
+        } else {
+            DPRINTF("Write gpio input port error!");
+        }
+        break;
+    case 0x10: /* GRER */
+    case 0x14: /* GFER */
+    case 0x18: /* GEDR */
+        break;
+    case 0x20: /* GPIR */
+        s->reg_GPIR = value;
+        break;
+    default:
+        DPRINTF("Bad offset 0x%x\n", offset);
+    }
+}
+
+static const MemoryRegionOps puv3_gpio_ops = {
+    .read = puv3_gpio_read,
+    .write = puv3_gpio_write,
+    .impl = {
+        .min_access_size = 4,
+        .max_access_size = 4,
+    },
+    .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int puv3_gpio_init(SysBusDevice *dev)
+{
+    PUV3GPIOState *s = FROM_SYSBUS(PUV3GPIOState, dev);
+
+    s->reg_GPLR = 0;
+    s->reg_GPDR = 0;
+
+    /* FIXME: these irqs not handled yet */
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW0]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW1]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW2]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW3]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW4]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW5]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW6]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW7]);
+    sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOHIGH]);
+
+    memory_region_init_io(&s->iomem, &puv3_gpio_ops, s, "puv3_gpio",
+            PUV3_REGS_OFFSET);
+    sysbus_init_mmio(dev, &s->iomem);
+
+    return 0;
+}
+
+static void puv3_gpio_class_init(ObjectClass *klass, void *data)
+{
+    SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+    sdc->init = puv3_gpio_init;
+}
+
+static const TypeInfo puv3_gpio_info = {
+    .name = "puv3_gpio",
+    .parent = TYPE_SYS_BUS_DEVICE,
+    .instance_size = sizeof(PUV3GPIOState),
+    .class_init = puv3_gpio_class_init,
+};
+
+static void puv3_gpio_register_type(void)
+{
+    type_register_static(&puv3_gpio_info);
+}
+
+type_init(puv3_gpio_register_type)