1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
|
<think>
Okay, so I'm looking at this log output from a system, and I need to figure out what's going on. Let me start by reading through each line carefully.
First, there are some PCI-related messages. It mentions "BAR" which stands for Bus Address Register, right? BAR 0 is assigned a memory region from 0x180000000 to 0x1807fffff as 64-bit pref. Then BAR 3 gets another memory region from 0x180800000 to 0x180807fff, also 64-bit pref. I'm a bit fuzzy on what exactly BARs are used for, but I think they're part of how the CPU communicates with devices over PCI.
Next, there's a message about pcieport 0000:00:04.0 being a bridge to bus 01. It also talks about bridge windows for IO and memory. The IO window is from 0x1000 to 0x1fff, which seems like a small range. Then there are two memory windows: one at fe800000-Fe9fffff and another much larger at 180000000-180bfffff as 64-bit pref.
Then, it switches to i40e driver messages. The driver is the Intel Ethernet Connection XL710 Network Driver. It's copyright from 2013 to 2019 by Intel. So this is an older driver maybe? Then it says enabling device (0140 -> 0142), which I'm not sure what that signifies, but probably the device state change.
The firmware version is given as 6.0.48442 with API 1.7 and NVM 6.01. The hardware IDs are [8086:1572] for vendor and product, and [8086:0008] for subsystem. Then the MAC address is listed as 3c:fd:fe:c0:59:98.
The driver mentions that FW LLDP is enabled, which I think stands for Link Layer Discovery Protocol. That's used for network discovery, so probably it's set up to detect other devices on the same switch or something.
Then there's a message about eth1 (the first Ethernet interface) having the NIC link up at 10 Gbps full duplex with no flow control. Okay, that makes sense; the connection is established and running smoothly.
Another line says that the device is operating at PCI-Express Speed 8.0GT/s Width x8. So it's a high-speed lane using all eight available lanes.
The features list includes PF-id[0] VFs:64 VSIs:66 QP:4 RSS FD_ATR FD_SB NTUPLE DCB VxLAN Geneve PTP VEPA. I'm not too familiar with all these acronyms, but I think they relate to different network offload features and virtualization support.
Then after some time, there's an IPv6 message indicating that eth1 link becomes ready, which is good for IPv6 connectivity.
Now comes the interesting part: at line 205.130288, pcieport reports that Slot(0) has Attention button pressed. Then it powers off due to the button press and says the card isn't present anymore. So someone must have pressed the attention button on a PCIe slot.
Finally, the i40e driver stops the PTP (Precision Time Protocol) on eth1 because the PHC (Pulse-Per-Second Clock) was removed.
Putting this all together, I think the system is an Intel-based server with an XL710 network card. The initial logs are about setting up the hardware and initializing the network interface. Then later, someone pressed the attention button on a PCIe slot, which caused the system to power down that slot's device (maybe a hotswap action?), and as a result, the network adapter's PTP service was stopped.
I'm not entirely sure about all the details here, like what each BAR assignment means or exactly how the attention button press affects the system. I might need to look up some of these terms to fully understand, but overall it seems like normal hardware initialization followed by a user intervention (pressing the PCIe slot's button) leading to the network interface being reset or powered off.
</think>
The log output details the initialization of an Intel Ethernet adapter and subsequent interaction with a PCIe slot. Here's a concise breakdown:
1. **PCI Initialization**: The system configures two 64-bit memory regions for the PCIe device (BARs), establishing communication channels for the network card.
2. **PCI Bridge Setup**: A PCIe port is set up as a bridge to another bus, enabling communication with devices on that bus, including IO and memory address ranges.
3. **Network Adapter Activation**: The Intel i40e driver initializes, setting up the Ethernet interface (eth1) with a MAC address and establishing a 10 Gbps connection in full duplex mode without flow control.
4. **Attention Button Press**: Approximately three minutes later, the system detects a press of the attention button on PCIe slot 0. This triggers a power-down of the device in that slot, leading to the removal of the Precision Time Protocol (PTP) service from eth1.
**Conclusion**: The logs show normal network adapter initialization followed by user intervention via the PCIe slot's attention button, resulting in the adapter being powered off and PTP services ceasing.
|