1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
|
<think>
Alright, let's try to figure out what's going on here. I'm looking at this log output from a Xen domain that was just created and restarted. The user mentioned they're seeing some panic messages, so I need to understand if this is normal or if there's an issue.
First, I see the guest system panicked with do_exit, do_group_exit, get_signal, etc. These are kernel functions related to handling signals and exits. Maybe something went wrong during a signal delivery. But since it restarted successfully, perhaps it's not a critical issue yet.
Looking further, after restarting, the domain connects to Open Firmware. There are messages about populating /vdevice methods and various devices like virtio block, serial, and scsi. The USB OHCI is initializing, which suggests the virtual USB controller is set up. Then there's a welcome message from Open Firmware, which is part of the firmware setup.
The system tries to boot but fails with "Not a bootable device" and "Load failed." It prompts for 'boot' or 'reset-all.' Maybe the virtual CD-ROM isn't correctly configured with an ISO image, so it can't find a bootable device. Alternatively, perhaps the storage devices aren't set up properly in the Xen configuration.
I should check if the domain has the necessary ISO attached and if it's correctly recognized as a bootable device. If not, maybe the user needs to add the ISO to the virtual CD-ROM or adjust the boot order. Also, ensuring that all devices are properly configured in the Xen setup might help prevent the panic and boot issues.
</think>
The log you've provided appears to be output from a Xen hypervisor environment, specifically related to the creation of a nested guest domain and its subsequent boot process. Here's a breakdown of what is happening:
### 1. **Initial Domain Creation and Panic**
- The system creates a new Xen domain (`nested-xenial`).
- A panic occurs during the initial stages of the domain's boot process, which triggers a restart of the guest.
- The panic backtrace shows functions like `do_exit`, `do_group_exit`, `get_signal`, and others being called. This suggests that the guest kernel encountered an error (panic) during its initialization.
### 2. **Guest Domain Reboots**
- After the panic, the guest domain is restarted.
- The system connects to the domain, populates virtual device methods (e.g., VirtIO devices for block storage, serial, and USB), and initializes hardware components like the network interface and CD-ROM.
### 3. **Open Firmware Boot Process**
- The guest enters the Open Firmware environment, which is a firmware layer used by some systems (notably IBM PowerPC-based systems).
- The system attempts to load from various devices but fails to find a bootable device, resulting in an error message: `E3404: Not a bootable device!` and `E3405: No such device`.
- This suggests that the guest domain may not have a valid bootable ISO image attached or configured properly.
### 4. **User Interaction**
- The system prompts for user input with options to either continue booting (`boot`) or reboot (`reset-all`).
---
### Key Points:
- The panic during domain creation may indicate an issue with the Xen hypervisor configuration or a problem with the guest OS.
- The failure to find a bootable device suggests that the guest domain is not properly configured with an ISO image or other bootable media.
- The system appears to be running in a nested virtualization environment, which can introduce additional complexity and potential issues.
### Recommendations:
1. **Check Domain Configuration:**
- Ensure that the Xen configuration for `nested-xenial` includes the necessary devices (e.g., VirtIO block, network, serial) and is properly set up.
- Verify that a valid ISO image is attached to the guest domain as the bootable media.
2. **Troubleshoot the Panic:**
- Investigate the panic backtrace to identify the root cause of the kernel exit. This may involve checking logs or debugging symbols if available.
3. **Ensure Proper Boot Device:**
- Attach a valid ISO image (e.g., an Ubuntu "xenial" ISO) to the guest domain's virtual CD-ROM.
- Verify that the boot order is correctly configured in the firmware.
4. **Check Xen Logs:**
- Review the Xen hypervisor logs for any additional error messages or warnings that may provide more insight into the issue.
If you're able to provide more details about how the guest domain was set up (e.g., configuration files, ISO images, etc.), I could help further diagnose the issue.
|